How to Use DualShock Calibration GUI on a PS4 or PS5 Controller
DualShock Calibration GUI is a free, open-source web app at dualshock-tools.github.io that recalibrates the analog sticks of a DualShock 4, DualSense or DualSense Edge. Plug the controller in with a USB cable, open the site in Chrome, Edge or Opera, press Connect, run Calibrate stick center and Calibrate stick range, test the result, then press Save changes permanently.
That is the whole job in one paragraph. The rest of this page is the detail that decides whether it goes well: which controllers it accepts, what each button really does, the difference between a temporary and a saved calibration, the DualSense Edge catch, and what the error messages mean. Everything about the tool below comes from the project's own code and help text, version 2.35 of 18 October 2026, not from forum lore.
Before you touch anything, take a reading so you have a number to compare against later. Hands off the sticks for the 10 seconds it samples:
What DualShock Calibration GUI is, and what it is not
The tool is a hobby project, MIT-licensed, written by a developer who goes by the_al with Mathias Malmqvist credited as the second developer. Its FAQ is frank about the method: DualShock and DualSense controllers answer some undocumented USB commands that are used during the factory assembly process, and the app sends those commands from your browser through WebHID. Nothing is installed on the computer, and the project states it has no connection to Sony.
What it can do is move the point the controller treats as "stick at rest" and the edge it treats as "stick fully tilted", then write those numbers into the controller itself. That is different from a deadzone in Steam or a game, which only ignores the first few percent of travel on one computer. The broader picture of where calibration sits next to deadzones, joy.cpl and Steam Input is on our general calibration page.
What it cannot do, in the project's own words: "This utility cannot fix stick drift." Drift comes from worn parts, dirt, a worn potentiometer or a tired spring, and the project warns that calibrating sticks that already drift "may also make the problem worse, with no way to undo it". If your reading above is past 10 %, read the stick drift page first; a new centre will not hold on a module that no longer returns to the same place twice.
What you need before you start
- A genuine Sony controller from the supported list (table below). Clones are detected and every calibration button is disabled for them; only Quick Test stays available.
- A USB data cable. Over Bluetooth the app refuses with "The device is connected via Bluetooth. Disconnect and reconnect using a USB cable instead."
- A browser with WebHID on a PC or Mac: Chrome, Edge or Opera. The page says Firefox works with a WebHID extension installed, though the project's Linux notes say Firefox has no WebHID on Linux. Safari has no WebHID, and the site states that phones and tablets are not supported.
- One controller connected at a time. The app asks for that explicitly.
- A charged battery that is plugged into the controller. This is the one rule that protects the hardware. Calibrating carries no risk, but if the cable drops during the split second of a save and there is no battery, or an empty one, the FAQ gives the controller "a high chance of being bricked".
- For a DualSense, firmware newer than 2020–2021 builds. The app blocks calibration on those and asks you to update first. A firmware update does not reset a saved calibration, according to the FAQ.
Which controllers it supports
The list is fixed in the code, by Sony's vendor ID 054C and these product IDs. Anything else does not even appear in the browser's device picker.
| Controller | Product ID | Stick centre | Range | Finetune | Restore older calibration | Save permanently |
|---|---|---|---|---|---|---|
| DualShock 4, first model | 05C4 | four-step | yes | no | no | yes |
| DualShock 4, second model | 09CC | four-step | yes | no | no | yes |
| DualSense | 0CE6 | quick or four-step | yes | yes | yes | yes |
| DualSense Edge | 0DF2 | quick or four-step | yes | yes | yes | only after a hardware mod |
| PS VR2 Sense, left and right | 0E45, 0E46 | four-step | yes | no | no | experimental |
The project calls its PS VR2 support "minimal and highly experimental", and says the author does not own those controllers to verify it.
How to use DualShock Calibration GUI, step by step
- Measure first. Run our stick drift test and write down the drift for each stick. Under 2 % is noise and a calibration may not change anything you can feel.
- Plug in by USB and open dualshock-tools.github.io in Chrome, Edge or Opera. On the first visit a welcome window repeats the battery rule and asks you to try a temporary calibration before saving. Press Understood.
- Press Connect and pick the controller in the browser's dialog. The page shows "Connected to:" with the model.
- Calibrate the centre. Open the arrow next to Calibrate stick center and choose a method (details in the next section). Do not close the page or pull the cable while it runs.
- Calibrate the range. Open the arrow next to Calibrate stick range, choose Use normal mode, and circle both sticks as described below until Done unlocks.
- Test without saving. Watch the LX, LY, RX, RY numbers in the stick view, switch to 10x zoom to see small offsets, and press Check circularity. Then run our drift test again in another tab and compare with step 1.
- Save or walk away. If the numbers are better, press the green Save changes permanently. If they are worse, press Reboot controller or unplug it, and the controller returns to the calibration it had before.
Centre calibration: quick or four-step
Calibrate stick center has two modes in its drop-down.
Use four-step calibration is a short wizard. The app asks you to push both sticks into a corner and let go, then press Continue once they have sprung back: top-left, top-right, bottom-left, bottom-right. The app samples where each stick settles after coming back from four directions. Once it starts it cannot be cancelled, so finish it. This is the only centre mode a DualShock 4 gets.
Use quick calibration recentres the sticks in one go while a "Calibrating center" window is open. The text does not ask you to move anything, so leave both sticks alone until it finishes. The code itself refers to this as the old, fully automatic method; the four-step wizard is the newer one and walks you through each sample, so it is the one to start with on a DualSense too.
Range calibration: how to rotate the sticks
Range calibration teaches the controller where full tilt is. When the window says "The controller is now sampling data!", push each stick against the edge of its gate and rotate slowly, at least twice in one direction and twice in the other. The FAQ adds the practical part: touch the edges of the frame and keep it slow. The progress bar can sit still for a while; the app tells you to keep rotating anyway.
In normal mode the Done button stays locked for up to 15 seconds. That delay is there for a reason. The most common complaint in the FAQ is "After range calibration, joysticks always go in corners", and the answer is that Done was pressed straight after the range calibration started. Most likely the controller then takes a small circle near the centre as its full range, so a light push already reads as maximum. Either way the fix is the same: run the range calibration again, properly.
Use expert mode hides the progress bar and enables Done at once. It saves up to 15 seconds for someone who already knows the motion and costs a redo for everyone else.
Temporary vs permanent: what "Save changes permanently" does
Every calibration, finetune or restore first changes only the controller's working state. While there are unsaved changes, Save changes permanently turns green and the page shows a banner that the controller "has unsaved changes that will be lost when the controller is rebooted". Unplug it, or press Reboot controller, and it goes back to its last saved calibration. Plug it back in with unsaved changes and the app reminds you to save or reboot.
That is a feature, not an inconvenience. It lets you try a calibration in a game for ten minutes before committing. The project recommends exactly that: test before saving.
Pressing the green button writes the new values into the controller's own storage. In the code, the save is an unlock of that storage followed by a lock, which is the moment when a dropped cable and a missing battery can brick the pad. After a successful save you see "Changes saved successfully". A failed one reads "Error while saving changes"; in that case check the cable and battery and try the save again.
A saved calibration lives in the controller, so it goes wherever the controller goes. The project does not say anything specific about how a saved calibration behaves once the controller is back on a PS4 or PS5; it only says the commands are the ones used at the factory. Check it the simple way: play on the console, then measure again on a PC with our test.
Restoring an older calibration and starting over
Changed your mind after saving? On a DualSense or DualSense Edge, Restore calibration lists earlier calibrations of that controller. Those are stored in your browser's local storage, not online, so they exist only in the browser you used, and clearing the cache or calibrating in an incognito window makes them irrecoverable. If the list is empty, the FAQ suggests rebooting the controller first. A restored calibration also has to be saved, or it disappears on the next reboot.
A DualShock 4 has no restore button. Once a DS4 calibration is saved, the only way back is another calibration. There is no "factory reset" for the sticks on any model; overwriting is always possible by calibrating again and pressing the green button.
Finetune: why not to aim for a perfect circle
Finetune stick calibration is for the DualSense and DualSense Edge only. It has two modes: Center (switch with L1), where you move a stick to select it and then nudge its centre with the D-pad without touching the stick, and Circularity (R1), where you push the stick straight up, down, left and right as far as it goes.
The circularity number trips people up. Check circularity reports an average error, and smaller looks better. The app says otherwise: aim for 7–9 %. Sony ships controllers calibrated to an average circularity error of nearly 10 %, games are tuned for that, and a stick that is too perfectly round can make aiming feel stiff in some games. The FAQ cites a sample of 30 DualSense Edge modules with an average of 8.6 %. So if your reading sits around 8 %, leave it.
DualSense Edge: why the save does not stick
The Edge keeps its calibration on each replaceable stick module, not in the controller body, which is why it travels with the module into another Edge. Those modules are write-protected. The project's own Edge window is blunt about it: the modules "cannot be calibrated via software alone".
Saving permanently needs a hardware modification on each module: applying +1.8 V to a write-protect test point, either with a thin wire soldered inside or applied from outside to the visible test point, while the save runs. The project marks this as experimental, for advanced users only, and takes no responsibility for damage. Without the mod you can still calibrate and play on the temporary result until the next reboot. Sony's console option for the Edge is a per-stick deadzone in its profiles, which hides an offset rather than moving the centre; the PS5 drift page covers that and module swaps.
Error messages and what to do
| What you see | What it means | What to do |
|---|---|---|
| Unsupported browser | The browser has no WebHID | Use Chrome, Edge or Opera on a PC or Mac |
| The device is connected via Bluetooth | The app needs USB | Reconnect with a USB data cable |
| The device appears to be a clone. All calibration functionality is disabled. | Not a genuine Sony controller, or one the app reads as such | Only Quick Test will work; if you are sure it is genuine, report it on the project's Discord or GitHub |
| This DualSense controller has outdated firmware | Firmware built in 2020 or 2021 | Update the controller on a PS5 or with Sony's firmware updater for Windows, then reconnect |
| NotAllowedError: Failed to open the device (Linux) | The browser has no permission for the device | Add a udev rule for the controller and use Chrome or Brave from a .deb or .rpm package, not Snap or Flatpak |
| Range calibration appears to have failed | Not enough stick movement was sampled | Repeat and rotate along the edge |
| Sticks pinned to the corners after range | Done was pressed too early | Run range calibration again |
| Error while saving changes | The write did not complete | Check cable and battery, then save again |
The Linux note in the project gives udev rules only for the DualSense and the second DualShock 4 model. Owners of a first DS4 or an Edge on Linux have to add a line with their own product ID from the table above; the project does not spell that out.
If the controller is not detected by the computer at all, the problem is before this tool; our controller not detected guide walks through cables, drivers and browsers in order.
Check the result
Run the stick drift test again with the same 10 seconds hands off and compare with your first reading. A good calibration brings a steady offset down and keeps it down on the next day's reading. If the number drops right after calibrating but creeps back within a week, the centre was never the problem: the module is wearing, and the honest options are a new module or a new controller, as the stick drift page explains. The deadzone test then tells you how small a deadzone you can get away with in games.
Questions people ask
Is DualShock Calibration GUI safe? Calibrating is low risk because nothing is stored until you save. The risk is a disconnect during the save with no working battery in the controller; keep the battery in and charged, and the cable firm.
Does it fix stick drift? No, and the project says so. It can correct a controller whose sticks rest slightly off centre. It cannot make a worn sensor read the same place twice.
Does it work over Bluetooth or on a phone? No. USB only, and only desktop browsers with WebHID.
Can I calibrate the triggers? Not yet. L2 and R2 calibration is on the project's to-do list, not in the app.
Does a firmware update undo my calibration? On a DualSense and DualSense Edge, the FAQ says no.
Why does my DualSense Edge lose its calibration after unplugging? Its stick modules are write-protected. Without the hardware mod, every calibration on an Edge is temporary.
Related
PS5 DualSense Stick Drift: Test, Fix, Replace →How to Calibrate a Controller on PC and PS5 →Stick Drift Test →What Is Stick Drift and How to Fix It →Sources: manufacturer and repair documentation listed in the text. Figures drawn by joy-stick.net.